Ethernet on Aaron's Worthless Words

Network Protocol Overhead

Mon, 10 Jan 2011 00:00:00 +0000

Here are some packet overhead numbers for a few popular protocols to help with doing bandwidth requirement calculations. This may be another add-as-we-go post, so please comment with additions or corrections.

Ethernet : 20 bytes
Frame Relay : 4 - 6 bytes
PPP : 6 bytes
MLPPP: 10 bytes
MPLS : 4 bytes

IP : 20 bytes

TCP : 20+ bytes
UDP : 8 bytes
GRE: 4 - 20+ bytes

IIUC Notes - Getting Phones on the LAN

Thu, 30 Sep 2010 00:00:00 +0000

More study notes. Correct if wrong, though I hope I get some of it right since I already since I’m an R&S guy. :$

**Switchport Configuration
**

switchport mode access: This config makes the port an access port that carries the primary and voice VLAN traffic
switchport mode trunk: This config akes the port a trunk unconditionally, but it will still send DTP messages
switchport nonegotiate: This config keeps the port from sending DTP messages.
switchport mode dynamic auto: If the port receives DTP messages, it will become a trunk. If not, it will be an access port.
switchport mode dynamic desirable: The port actively sends DTP messages trying to become a trunk. This is the default configuration on a Cisco switch.

Cisco IP Phone Boot Process

IIUC Notes - Assigning Ephone-dns to Ephone Buttons

Thu, 23 Sep 2010 00:00:00 +0000

These are some of my notes on my IIUC studies. Since I am a novice as voice stuff, please let me know what I get wrong.

An ephone is a representation of a phone. It’s basically a structure of features that a phone will have.

Configuration in CME:

R1(config)#ephone 34 <– This is just a tag and has nothing to do with an extension or phone
R1(config-ephone)#mac-address 1111.2222.3333 <– Assigns this ephone to the phone with that MAC address

IIUC Notes - Powering Cisco Phones

Tue, 21 Sep 2010 00:00:00 +0000

Feel free to correct anything that is wrong or incomplete.

Power over Ethernet (PoE)
- Can provide power to a Cisco phone, access point, security camera, etc., through the network cabling, eliminating the need to plug the phone into the wall for power.
- Generic term for providing power on the Ethernet cable
- Provides centralized power that can be put on a UPS
- Allows devices to be located away from power outlets
- Removes cabling clutter at the user’s desk
- Can be provided through PoE-enabled switches, power panels or inline couplers (power injectors)
- Oversubscription is common
  - If every device on a switch asks for full power, the switch may not be able to handle the load.
- Of course, devices can be powered with a power brick at the desk
802.3af

Server NIC Aggregation to a Cisco Switch

Tue, 14 Apr 2009 00:00:00 +0000

Have you even noticed that your new servers all have 2 NICs on the board? At least all of them that I’ve seen in the last 3 years have. A lot of server admin actually use them in a NIC teaming scenario where both NICs are used as one logical device – much the same as Etherchannel on a switch. This provides some fault tolerance and availability in case of failure, which is good idea in most cases.

Make Your Own Ethernet Cables

Wed, 29 Aug 2007 00:00:00 +0000

If you need to buy an Ethernet cable, you’ll pay quite a premium for it at your local CompUSA or Circuit City. $22.99 for a 7’ Ethernet cable is terrible. For just a few dollars more, you can buy a 250’ roll of cable and make 35 of them yourself. You’ll need to invest in a good crimper and some RJ45 heads as well, but that cost is quite small compared to how much you can save by making your own.